Ign Corr Logs explained

Announcements, dicussion about any topic that would have broad interest to the forum members

Moderator: Freon

Ign Corr Logs explained

Postby riderz4101 » Thu Oct 12, 2006 4:02 am

Hi, would like to know what the following log events represent

Ign Correction (Learnt Corr)
Ign Corr (Coarse corr)
Ign Corr (Neg Knock comp)

Thanks
riderz4101
 
Posts: 10
Joined: Wed Jul 12, 2006 12:21 pm
Location: Trinidad

Postby riderz4101 » Mon Oct 16, 2006 7:48 am

Anything yet on this.
riderz4101
 
Posts: 10
Joined: Wed Jul 12, 2006 12:21 pm
Location: Trinidad

Re: Ign Corr Logs explained

Postby west_minist » Sat Nov 25, 2006 8:09 pm

riderz4101 wrote:Hi, would like to know what the following log events represent

Ign Correction (Learnt Corr)
Ign Corr (Coarse corr)
Ign Corr (Neg Knock comp)

Thanks

To the best of my knowleadge and info gain during logging
Respectively:
1. Ign learnt as the ecu learns with the specify rpm and load range in the 1D Coarse Ign Learning maps. These values can be +-ve. There are small corrections to main ignition map, except when -ve. Knock correction is affect by these values. There are instances where the Neg. Knock comp is 0, and these show negatives values. This is normally outside the Knock rpm range. It is like staying, I am hearing sometime, I am not sure what it is, since it is outside my knock monitoring, but hey, let me correct the timing. This is way above 6500rpm.

2. This seems to be the Ignition Correction table values and as expected, affected by the IAM. The Knock Correction curves follows this curves, once no knock is detected. KC= Ign Coarse corr[~(IAM/16)] + Ign learnt corr + n[Neg Knock comp where n~1. This is not an exact equation, but it should demonstrate a point.

3. When Knock/pinging is detected and base on the ECU set threshold, this value removes timing or adjusted the correct to protect the engine. The ranges are defined in the ecu 1D maps
west_minist
 
Posts: 515
Joined: Fri Jan 07, 2005 1:31 pm
Location: Barbados

Postby west_minist » Sat Nov 25, 2006 9:08 pm

Below is an STI with serious problems. IAM even went to zero, but for this topic, the trouble log was used to determine the behaviour of the named ign variables to one another and ECU settings.

Log window shows:-
Knock Corrections - RED
Ign. Corr. AK (Neg. Knock Comp.) - BLUE
Ign. Corr. AP (Learnt Correc) - GREEN
Ign. Corr. AT (Coarse Correc.) - ORANGE

Image


Log window shows:-
Knock Corrections - RED
Ign. Corr. AK (Neg. Knock Comp.) - BLUE
Ign. Corr. AP (Learnt Correc) - GREEN
Ign. Corr. AT (Coarse Correc.) - ORANGE

Image
west_minist
 
Posts: 515
Joined: Fri Jan 07, 2005 1:31 pm
Location: Barbados

Postby Fbartolo » Sun Jan 13, 2008 9:11 am

Fbartolo
 
Posts: 3
Joined: Mon Jul 04, 2005 1:45 am
Location: Paris


Return to General Discussion

Who is online

Users browsing this forum: No registered users and 0 guests