This has not been said enough around here

[cossie1]

That info is taken from a thread on the MLR, the guy that posted it, has done this mod to an evo 6 using an evo 7 ecu.

Can you post or PM me a link to that thread?

Here is the link. The info I have pasted onto here is from page 3.

http://www.lancerregister.com//showthread.php?s=&threadid=142077

[cossie1]

For some reason flashecu can't connect to my ecu to dump the rom

Comes up saying:

Using interface OpenPort 1.3 Universal
TX26pDkE6d0437d539f0b74e1f839ca8e61c0abf91fb0f09

sending init sequence 2

Then fails and says read the log.

Anyone have any ideas ?

The car is Evo 6 RSII

[gteclass]

same issue here cossie

[BarryC.]

sorry for not replying dudes been very busy,
anyway done a download again today for ye and it goes straight to init2,
have a look

[11:35:34.874] Version 1.31.1396
[11:35:34.884] 11 memory models read.
[11:35:34.884] scanning for metadata models in C:/Program Files/OpenECU/EcuFlash/rommetadata
[11:35:36.076] 234 ROM metadata models scanned.
[11:35:36.076] checksum module "subarudbw" loaded.
[11:35:36.076] flashing tool "wrx02" loaded.
[11:35:36.076] flashing tool "wrx04" loaded.
[11:35:36.076] flashing tool "sti04" loaded.
[11:35:36.076] flashing tool "sti05" loaded.
[11:35:36.076] flashing tool "mitsukernel" loaded.
[11:35:36.076] flashing tool "mitsukernelocp" loaded.
[11:35:36.076] flashing tool "shbootmode" loaded.
[11:35:52.379] Using interface OpenPort 1.3 Universal TX25L*DU8044f6c914e91098ab7432b1ea9d25d750e713e9
[11:35:55.554] sending init sequence 2
[11:35:55.574] got 0x11 response
[11:35:55.574] sending init sequence 3
[11:35:55.994] entering bootloader
[11:35:56.025] sending kernel size (1531)
[11:35:56.065] sending kernel load address (0x0000F000)
[11:35:56.085] uploading kernel
[11:35:56.345] verifying kernel checksum response
[11:35:56.355] kernel valid
[11:35:56.565] kernel get version
[11:35:56.585] kernel debug:
[11:35:56.595] [B0] F2 A8 F0 36 F5 01 00 07 05 FB F0 00 B8 80
[11:35:56.605] kernel version is : OpenEcu Mitsubishi H8/539F Kernel V0.13
[11:35:56.605] reading kernel comm buffer size
[11:35:56.625] comm buffer size set to 256
[11:35:56.625] reading kernel flash buffer size
[11:35:56.655] flash buffer size set to 1024
[11:35:56.655] kernel read area: addr: 0000FEE0 len: 0001
[11:35:56.685] kernel read area: addr: 0000FEE2 len: 0001
[11:35:56.696] kernel read area: addr: 0000FEE3 len: 0001
[11:35:56.716] kernel read area: addr: 0000FF15 len: 0001
[11:35:56.726] flmcr: 80 ebr1: 00 ebr2: 00 ramcr: b8
[11:35:56.736] Dumping ECU memory...
[11:35:56.776] kernel read area: addr: 00010000 len: 0400

[gteclass]

sorry for not replying dudes been very busy,
anyway done a download again today for ye and it goes straight to init2,
have a look

[11:35:34.874] Version 1.31.1396
[11:35:34.884] 11 memory models read.
[11:35:34.884] scanning for metadata models in C:/Program Files/OpenECU/EcuFlash/rommetadata
[11:35:36.076] 234 ROM metadata models scanned.
[11:35:36.076] checksum module "subarudbw" loaded.
[11:35:36.076] flashing tool "wrx02" loaded.
[11:35:36.076] flashing tool "wrx04" loaded.
[11:35:36.076] flashing tool "sti04" loaded.
[11:35:36.076] flashing tool "sti05" loaded.
[11:35:36.076] flashing tool "mitsukernel" loaded.
[11:35:36.076] flashing tool "mitsukernelocp" loaded.
[11:35:36.076] flashing tool "shbootmode" loaded.
[11:35:52.379] Using interface OpenPort 1.3 Universal TX25L*DU8044f6c914e91098ab7432b1ea9d25d750e713e9
[11:35:55.554] sending init sequence 2

when i try to read mine it looks more like that!

[BarryC.]

ok I know this is probably a stupid question but you do have the white initialisation plug connected???

[cossie1]

Yes I have the white connector connected.

If I leave the lead plugged in, and just swap to the e7 ecu, I can read and write it no problems.

Well have to write to it twice for some reason as it fails on first go, but point is it will connect and dump / write to it.

[cossie1]

Barry can you do me a big favour please, and check your port settings for the openport cable in the device manager of windows xp.

Maybe just maybe there is a slightly different setting and thats why your the only 1 on here so far that has it working

[BarryC.]

yep my settings are
Com port 2 as the virtual port software makes the cable com 2
9600 bits
FTDIBUS\VID_0403+PID_CC4A+TX25L*DUA\0000

[cossie1]

yep my settings are
Com port 2 as the virtual port software makes the cable com 2
9600 bits
FTDIBUS\VID_0403+PID_CC4A+TX25L*DUA\0000

Can you go into advanced settings on the com port for the openport lead please and let me know what settings are in there.

Cheers

[BarryC.]

com 2 latency and transmit set to 4096 timer 16ms serial emulator ticked,
I am trying to get my hands on an Evo 6 Ecu to test it wouldnt mind I just sold one

[cossie1]

com 2 latency and transmit set to 4096 timer 16ms serial emulator ticked,
I am trying to get my hands on an Evo 6 Ecu to test it wouldnt mind I just sold one

Always the way ain't it.

I used to have a couple of spares, but sold them after selling the other evo's

[cossie1]

try and get an RA420996R1 whilst your at it m8

[BarryC.]

try and get an RA420996R1 whilst your at it m8

Evo 6 ralliart rom will do

[cossie1]

try and get an RA420996R1 whilst your at it m8

Evo 6 ralliart rom will do

Yeh well if you can find the Ralliart Ecu to borrow, then you get to kill 2 birds with 1 stone

Get to dump an evo 6 ecu, and get a decent dump from it too