openecu.org

This is the ROM from an Aus GT Forester. I think it's pretty similar to the Aus '01 WRX in definition. Can anyone give me a hand on the .XML definitions for this?

Michael.


*Attachment removed - my screw up!!! *

Here is a start. I am not sure if the ignition Correction map is correct ro even one at all.

<ecu_struct id="A4SE700F" type="Aus GT Forester" include="" desc_size="#30000" reverse_bytes="True">
<map name="Low Det Fuel Map" type="3" active="1" help="" level="0">
<rows count="18" func_2val="toRPM()" func_val2="frRPM()" offset="#29275" power="2" signed="False" format="%.0f" caption="" desc="RPM"/>
<cols count="16" func_2val="toLoad()" func_val2="frLoad()" offset="#29299" power="2" reverse_bytes="False" signed="False" format="%.2f" caption="" desc="Load (g)"/>
<data order="cr" func_2val="toAFR()" func_val2="frAFR()" offset="#292BC" power="1" signed="False" format="%.2f" caption="" desc="Air-to-Fuel Ratio" color_dir="1" inc="1" incb="5" inc_dir="1"/>
</map>
<map name="High Det Fuel Map" type="3" active="1" help="" level="0">
<rows count="18" func_2val="toRPM()" func_val2="frRPM()" offset="#293EB" power="2" signed="False" format="%.0f" caption="" desc="RPM"/>
<cols count="16" func_2val="toLoad()" func_val2="frLoad()" offset="#2940F" power="2" reverse_bytes="False" signed="False" format="%.2f" caption="" desc="Load (g)"/>
<data order="cr" func_2val="toAFR()" func_val2="frAFR()" offset="#29432" power="1" signed="False" format="%.2f" caption="" desc="Air-to-Fuel Ratio" color_dir="1" inc="1" incb="5" inc_dir="1"/>
</map>
<map name="Ignition Map" type="3" active="1" help="" level="0">
<rows count="18" func_2val="toRPM()" func_val2="frRPM()" offset="#29A00" power="2" signed="False" format="%.0f" caption="" desc="RPM"/>
<cols count="16" func_2val="toLoad()" func_val2="frLoad()" offset="#29A24" power="2" reverse_bytes="False" signed="False" format="%.2f" caption="" desc="Load (g)"/>
<data order="cr" func_2val="toIgn()" func_val2="frIgn()" offset="#29A47" power="1" signed="False" format="%.2f" caption="" desc="Degrees" color_dir="0" inc="1" incb="5" inc_dir="1"/>
</map>
<map name="Ignition Correction Map" type="3" active="1" help="" level="0">
<rows count="18" func_2val="toRPM()" func_val2="frRPM()" offset="#29FD0" power="2" signed="False" format="%.0f" caption="" desc="RPM"/>
<cols count="16" func_2val="toLoad()" func_val2="frLoad()" offset="#29FF4" power="2" reverse_bytes="False" signed="False" format="%.2f" caption="" desc="Load (g)"/>
<data order="cr" func_2val="toIgnC()" func_val2="frIgnC()" offset="#2A017" power="1" signed="False" format="%.2f" caption="" desc="Degrees" color_dir="0" inc="1" incb="5" inc_dir="1"/>
</map>

Awesome, thanks mate. I'm still learning about all this so that is a huge help.

Thanks again,

Michael.

I don't suppose anyone has the stock Forester GT or Euro S/Turbo map they can put up for comparison?

Michael.

Did anyone get a std map for a MY01 S-Turbo or GT ?

Andrew...

msjo wrote:I don't suppose anyone has the stock Forester GT or Euro S/Turbo map they can put up for comparison?

Michael.

Hi Micheal, I have a GT MY01 MT rom if you still need it?

Hi all,

Want to tune a Aus forester GT MY01 and I was wondering if anyone has any luck in doing so.

Does any one know if the ECU in the Aus GT is the same as the Euro MY01 S-Turbo model?

Are the ecu maps the same?

Thanks,

FGT