type = ssmcan
paramname = A/F_Sensor_#1(AFR)
paramid = 0x000046
databits = 8
scalingrpn = x,128,/,14.7,*
paramname = IAM(multiplier)
paramid = 0x0000F9
databits = 8
scalingrpn = x,16,/
paramname = Engine_Load_(4-Byte)*(g/rev)
paramid = 0xFF65D4
isfloat = 1
scalingrpn = x
paramname = CL/OL_Fueling*(status)
paramid = 0xFF9CF1
databits = 8
scalingrpn = x,6,+
paramname = Fine_Learning_Knock_Correction_(4-byte)*(degrees)
paramid = 0xFF7CDC
isfloat = 1
scalingrpn = x
paramname = Knock_Correction_Advance_(4-byte)*(degrees)
paramid = 0xFF7C3C
isfloat = 1
scalingrpn = x
paramname = Fuel_Injector_#1_Latency_(4-byte)*(ms)
paramid = 0xFF6F44
isfloat = 1
scalingrpn = x,.001,*
paramname = Manifold_Absolute_Pressure_(4-byte)*(bar_absolute)
paramid = 0xFF63FC
isfloat = 1
scalingrpn = x,0.001333224,*
paramname = Ignition_Base_Timing*(degrees)
paramid = 0xFF7988
isfloat = 1
scalingrpn = x
paramname = Requested_Torque*(raw_ecu_value)
paramid = 0xFF7FA4
isfloat = 1
scalingrpn = x
paramname = A/F_Correction_#1_(2-byte)**(%)
paramid = 0xFF6A2A
databits = 16
scalingrpn = x,.01220703,*,100,-
paramname = A/F_Sensor_#1_(2-byte)**(estimated_AFR)
paramid = 0xFF6A18
databits = 16
scalingrpn = x,.0001220703,*,14.7,*
paramname = IAM_(1-byte)**(multiplier)
paramid = 0xFF6A4F
databits = 8
scalingrpn = x,.0625,*
paramname = defogger_sw
paramid = 0x64
databits = 1
offsetbits = 5
isvisible = 0
conditionrpn = defogger_sw,1,==
Action = start
conditionrpn = defogger_sw,0,==
action = stop
20091101091946 ERROR logcfg Form1 loadDefs ERROR:5(10150) Invalid procedure call or argument
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10160) Object required
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10170) Object required
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10200) Object required
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10220) Object required
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10200) Object required
20091101091946 ERROR logcfg Form1 loadDefs ERROR:424(10220) Object required
freakin wrote:apart from RPM and the defogger what are the common on/off controls?
conditionrpn = engine_speed,1,==
Action = start
conditionrpn = defogger_sw,0,==
action = stop
;conditionrpn = defogger_sw,1,==
;action = start
;conditionrpn = defogger_sw,0,==
;action = stop
Return to Openport Stand-Alone Logging Beta
Users browsing this forum: No registered users and 28 guests