M32R

Links to development tools which have been useful to this project

Moderator: Freon

M32R

Postby Marmes » Wed Jan 02, 2008 2:29 pm

Hello!
Does anyone have some tools for M32R processors?

Thanks!
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

Postby wmcdonal » Tue Jan 22, 2008 7:52 pm

Yes, what exactly are you looking for ?
wmcdonal
 
Posts: 5
Joined: Thu Dec 07, 2006 5:17 pm
Location: Australia

Postby salex » Wed Jan 23, 2008 2:44 pm

Renesas has a tool for flashing the evaluation boards containing it.
It is called M3S-UFLA32R, but it is only able to flash - not read.

Any other ideas? :)
salex
 
Posts: 72
Joined: Wed Jun 21, 2006 2:30 pm
Location: Greece

Postby Marmes » Wed Jan 23, 2008 2:48 pm

After reading some datasheets, It seems that everything to be able to read the flash is there explained,doesn't seem to be very hard.
It even says that the only protection this processor has is a pin pulled to to a state Low to prevent the ecu to be read or written, I know there are other kind of protections ,the ones used by some companies here to protect their work where they set an ID.
What we need is a simple iso 9141 interface with some dc to dc converter to pull the voltage up to disable the protection.
But this is me guessing.
Cheers!
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

Postby salex » Sun Jan 27, 2008 9:16 am

The manuals seem very interesting. I wonder what sort of interface we might be able to build following the instructions!
salex
 
Posts: 72
Joined: Wed Jun 21, 2006 2:30 pm
Location: Greece

Postby Marmes » Wed Jan 30, 2008 9:38 am

I think what it's needed is to put the FP in High state to put processor in boot mode and read.

This is me guessing again :S
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

Postby salex » Wed Jan 30, 2008 1:02 pm

Marmes wrote:I think what it's needed is to put the FP in High state to put processor in boot mode and read.

This is me guessing again :S


That is the main idea, but it will take more than the instructions in the manual to be able to read. Boot mode supports writing in this one :-)
salex
 
Posts: 72
Joined: Wed Jun 21, 2006 2:30 pm
Location: Greece

Postby Marmes » Wed Jan 30, 2008 1:52 pm

What can we do to read it?, can we use the tactrix cable for mistubishi?
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

Is the MR32 this ones?

Postby christian_piasini » Sun Feb 03, 2008 2:05 am

Hello, it is the MR32 the mcu you see in the picture below?




Regards


Christian Piasini
R&D Piasiniengineering
Attachments
DSCN0949.JPG
DSCN0949.JPG (202.18 KiB) Viewed 17964 times
christian_piasini
 
Posts: 101
Joined: Sat Nov 25, 2006 8:50 am
Location: Italy

Postby Marmes » Sun Feb 03, 2008 5:53 am

yes it is.
you think its not?
Then explain yourself :)

Best Regards!
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

I think is...

Postby christian_piasini » Fri Feb 08, 2008 9:37 am

Yes it is, I joke ....

some times as well has to joke a little bit.....

Regards


Christian Piasini
R&D Piasiniengineering
christian_piasini
 
Posts: 101
Joined: Sat Nov 25, 2006 8:50 am
Location: Italy

Postby Marmes » Fri Feb 08, 2008 11:08 am

that one has a jtag port, i think it is...
Marmes
 
Posts: 38
Joined: Tue Nov 20, 2007 8:49 am

I don't need the Jtag port

Postby christian_piasini » Fri Feb 08, 2008 2:08 pm

With this ecu we don't need to read it trough the JTAG....

we do it trough the ecu plug, without open it...


Regards


Christian Piasini
R&D Piasiniengineering
christian_piasini
 
Posts: 101
Joined: Sat Nov 25, 2006 8:50 am
Location: Italy


Return to Development Tools

Who is online

Users browsing this forum: No registered users and 5 guests