2008 EDM STI dont read map using Ecuflash
Posted: Fri Dec 07, 2012 11:43 am
Hi to everybody,
First of all excuse me if my english is not good, i am writing from Italy
Also excuse me if this is not the correct section
Just need an info on what is happening on my 2008 STI that i have bought second hand last week.
Well, i have upgraded in these years from a 2002 STI to a MY 2007 and now i bought a MY 2008 model (hatch) and always have flashed by myself my ecus without any problem.
Last night just connected the openport 2.0 to the car and i get this messages on the log:
[20:44:28.629] EcuFlash Version 1.42.2595
[20:44:28.629] OS Version Windows XP
[20:44:28.629] Qt Version 4.5.0
[20:44:28.649] 56 memory models read.
[20:44:28.649] scanning for metadata models in C:/Programmi/OpenECU/EcuFlash/rommetadata
[20:44:28.829] 343 ROM metadata models scanned.
[20:44:28.829] checksum module "subarudbw" loaded.
[20:44:28.829] checksum module "mitsucan" loaded.
[20:44:28.829] flashing tool "wrx02" loaded.
[20:44:28.829] flashing tool "wrx04" loaded.
[20:44:28.829] flashing tool "sti04" loaded.
[20:44:28.829] flashing tool "sti05" loaded.
[20:44:28.829] flashing tool "mitsukernel" loaded.
[20:44:28.829] flashing tool "mitsukernelocp" loaded.
[20:44:28.829] flashing tool "mitsubootloader" loaded.
[20:44:28.829] flashing tool "shbootmode" loaded.
[20:44:28.829] flashing tool "shaudmode" loaded.
[20:44:28.829] flashing tool "subarucan" loaded.
[20:44:28.829] flashing tool "mitsucan" loaded.
[20:44:34.557] J2534 API Version: 04.04
[20:44:34.557] J2534 DLL Version: 0.50.2598 Jun 26 2009 15:02:29
[20:44:34.557] Device Firmware Version: 1.10.2658
[20:44:36.140] kernel get version
[20:44:36.360] SSM2 init
[20:44:36.390] SSM2 ECU ID is 5A 42 78 42 07
[20:44:36.390] Requesting Seed...
[20:44:36.400] Sending Key...
[20:44:36.400] interface close
[20:44:36.420] interface close
Well, i dont know if car is still reflashed and the previous owner does not know because was the 3th° owner.
Car have some mods like upgraded water radiator, intercooler and oil cooler so i assume probably have been reflashed in the past but i have no acces to this information.
I removed the ecu from under the carpet on the passeger side to take a look and i found the two green test connectors near the ecu, tried to read with connector plugged togheter (like my old 2007 sti) but still same result.
Tried to read as 2005-2007 DBW STI or 2007+ DBW CAN STI but still same result
I was thinking that probalby was the openport 2.0 that was not running so i readed and modified the map from a 2008 Forester XT of a friend and everything goes fine.
Any idea?
I am seriously thinking that car had and Ecutek remap and now is locked.
In this case how i can discover this and unlock it ?
There are no Ecutek dealers in my area, the nearest one is 600km away!!!
Thank you in advance
Regards
Luigi
First of all excuse me if my english is not good, i am writing from Italy
Also excuse me if this is not the correct section
Just need an info on what is happening on my 2008 STI that i have bought second hand last week.
Well, i have upgraded in these years from a 2002 STI to a MY 2007 and now i bought a MY 2008 model (hatch) and always have flashed by myself my ecus without any problem.
Last night just connected the openport 2.0 to the car and i get this messages on the log:
[20:44:28.629] EcuFlash Version 1.42.2595
[20:44:28.629] OS Version Windows XP
[20:44:28.629] Qt Version 4.5.0
[20:44:28.649] 56 memory models read.
[20:44:28.649] scanning for metadata models in C:/Programmi/OpenECU/EcuFlash/rommetadata
[20:44:28.829] 343 ROM metadata models scanned.
[20:44:28.829] checksum module "subarudbw" loaded.
[20:44:28.829] checksum module "mitsucan" loaded.
[20:44:28.829] flashing tool "wrx02" loaded.
[20:44:28.829] flashing tool "wrx04" loaded.
[20:44:28.829] flashing tool "sti04" loaded.
[20:44:28.829] flashing tool "sti05" loaded.
[20:44:28.829] flashing tool "mitsukernel" loaded.
[20:44:28.829] flashing tool "mitsukernelocp" loaded.
[20:44:28.829] flashing tool "mitsubootloader" loaded.
[20:44:28.829] flashing tool "shbootmode" loaded.
[20:44:28.829] flashing tool "shaudmode" loaded.
[20:44:28.829] flashing tool "subarucan" loaded.
[20:44:28.829] flashing tool "mitsucan" loaded.
[20:44:34.557] J2534 API Version: 04.04
[20:44:34.557] J2534 DLL Version: 0.50.2598 Jun 26 2009 15:02:29
[20:44:34.557] Device Firmware Version: 1.10.2658
[20:44:36.140] kernel get version
[20:44:36.360] SSM2 init
[20:44:36.390] SSM2 ECU ID is 5A 42 78 42 07
[20:44:36.390] Requesting Seed...
[20:44:36.400] Sending Key...
[20:44:36.400] interface close
[20:44:36.420] interface close
Well, i dont know if car is still reflashed and the previous owner does not know because was the 3th° owner.
Car have some mods like upgraded water radiator, intercooler and oil cooler so i assume probably have been reflashed in the past but i have no acces to this information.
I removed the ecu from under the carpet on the passeger side to take a look and i found the two green test connectors near the ecu, tried to read with connector plugged togheter (like my old 2007 sti) but still same result.
Tried to read as 2005-2007 DBW STI or 2007+ DBW CAN STI but still same result
I was thinking that probalby was the openport 2.0 that was not running so i readed and modified the map from a 2008 Forester XT of a friend and everything goes fine.
Any idea?
I am seriously thinking that car had and Ecutek remap and now is locked.
In this case how i can discover this and unlock it ?
There are no Ecutek dealers in my area, the nearest one is 600km away!!!
Thank you in advance
Regards
Luigi