openecu.org

by **nvr2fast** » Sun Oct 01, 2006 11:50 am

Tell them to make donation then! This will help to motivate him to work faster hehe :lol:

by **west_minist** » Mon Oct 02, 2006 4:45 pm

bmorrisj wrote:
west_minist wrote:I cannot get 1.29 to connect or use the cable.

Cbole, any ideas?

I do not have the port settings under options.

i had the same problem... but i updated the cable drivers with the files in the 'drivers' directory...

Ok. Let me try that.

by **laakness** » Tue Oct 03, 2006 3:33 pm

I have a similar issue where I can't write to the ECU. I tried reading and it gets to address 00013C00 and gives me "rkrv: bad checksum".

I've used all the other versions without issue so it's probably the cable driver that I need to update. I will give that a shot and post back.

by **cboles** » Tue Oct 03, 2006 4:18 pm

Interesting. The dpinst.exe that is in the drivers directory gets run during the install. I'm not sure why it would need to be run twice...

Colby

bmorrisj wrote:
west_minist wrote:I cannot get 1.29 to connect or use the cable.

Cbole, any ideas?

I do not have the port settings under options.

i had the same problem... but i updated the cable drivers with the files in the 'drivers' directory...

by **west_minist** » Tue Oct 03, 2006 4:27 pm

I had uninstall the drivers from the add/remove and reinstall from the directory.

With the new 1.29, I am not sue if I can read a DBW now. My colleagues in Trinidad will try for me.

by **laakness** » Tue Oct 03, 2006 7:06 pm

When I installed the latest version it did not run the FTDI driver setup like previous versions had.

cboles wrote:Interesting. The dpinst.exe that is in the drivers directory gets run during the install. I'm not sure why it would need to be run twice...

Colby

bmorrisj wrote:
west_minist wrote:I cannot get 1.29 to connect or use the cable.

Cbole, any ideas?

I do not have the port settings under options.

i had the same problem... but i updated the cable drivers with the files in the 'drivers' directory...

by **Cabal** » Wed Oct 04, 2006 5:20 am

laakness wrote:When I installed the latest version it did not run the FTDI driver setup like previous versions had.

Same here. Running it manually from the drivers directory worked nicely.

by **cboles** » Wed Oct 04, 2006 8:57 am

I have fixed this and released a new "1.29a" version. The only difference is in the installer. EcuFlash is the same.

by **laakness** » Wed Oct 04, 2006 4:10 pm

Thanks!

by **bmorrisj** » Wed Oct 04, 2006 8:13 pm

laakness wrote:When I installed the latest version it did not run the FTDI driver setup like previous versions had.

cboles wrote:Interesting. The dpinst.exe that is in the drivers directory gets run during the install. I'm not sure why it would need to be run twice...

Colby

bmorrisj wrote:
west_minist wrote:I cannot get 1.29 to connect or use the cable.

Cbole, any ideas?

I do not have the port settings under options.

i had the same problem... but i updated the cable drivers with the files in the 'drivers' directory...

i didnt run a driver installer, i just manually updated the drivers via device manager...

by **laakness** » Fri Oct 06, 2006 12:56 pm

Running the newest 1.29a with the updated driver install fixed my read/write issue.

Guess I'm glad I did a read that failed before doing a write that failed

openecu.org

ECUFlash updates?

Who is online