EVO5/6 MH7201F - MH7202F read/flash tool - it works.

[Travis]

we are still having read problems on some h8 machines, it will probly be a while still.

damn. sooo my ecu read just fine. is there any info I can give you to help?

[gteclass]

What car do you have? You could post your rom so I can look at it and compare it to the 2000 fed spec eclipse gt rom i already have and the evo 5 rom that i picked up somewhere. I have someone trying to bring me a gsx to read but i havent seen it yet.

[cossie1]

What car do you have? You could post your rom so I can look at it and compare it to the 2000 fed spec eclipse gt rom i already have and the evo 5 rom that i picked up somewhere. I have someone trying to bring me a gsx to read but i havent seen it yet.

Do you have a definition file for the evo 5 rom ??

[Travis]

What car do you have? You could post your rom so I can look at it and compare it to the 2000 fed spec eclipse gt rom i already have and the evo 5 rom that i picked up somewhere. I have someone trying to bring me a gsx to read but i havent seen it yet.

Here's the ROM and Definition file. The ROM is from my ecu and I think you made the def...(I'm kobalt82 on c3g)

[gteclass]

ok, well thanks for posting it, anyone able to read a cali spec h8 car yet?

[06rexwagon]

Hey Travis, I'll be watching this thread so if you get flash support we can tune your car.

[Travis]

Hey Travis, I'll be watching this thread so if you get flash support we can tune your car.

Thanks

[MattS00]

Im curious if anyone knows if there is any new information?

I have a 2000 eclipse gt fed spec, so I could possibly pull off an ecu swap with a flashable late 2001+ h7 ecu. I need to start researching ecu pin outs to make sure.

There are a few pit falls that I know of at this time. The cam position sensor reluctor in the distributor for 2000 and 2001 cars has one sensing blade. The 2002+ distributors have 4 sensing blades. Without fixing the problem cam and crank position sensor codes will be thrown. There is the option of swaping the reluctor, but I'm not 100% sure the signal would not be a degree or two off. However, I have read of one successful swap on a 2000 cali spec. TheFranchise on club3g.com used a 2002 ecu, flashed to delete the immobilizer deleted, and flashed it with a late 2001 rom.

My fed spec car has 2 o2 sensors total, and fuel trims control all 6 cylinders. All flashable eclipse v6 ecus are cali spec emmissions and have 4 o2 sensors with individual fuel trims for each bank of cylinders. This would require me to weld in bungs for 4 new o2 sensors.

[Sanctifier]

... Guess we need to find someone with an Evo 5/6 RA ecu (RA420996R1) to dump now.

I have an E6 RalliArt Sport ECU (RA420996R1.)
Not much point adding to the confusion now.
When Colby sorts out the kernel then I can add this to the other maps.

[cossie1]

... Guess we need to find someone with an Evo 5/6 RA ecu (RA420996R1) to dump now.

I have an E6 RalliArt Sport ECU (RA420996R1.)
Not much point adding to the confusion now.
When Colby sorts out the kernel then I can add this to the other maps.

Have you managed to dump the rom yet ?

[Sanctifier]

... Have you managed to dump the rom yet ?

Nope. Haven't bothered. When Colby sorts out the software then I'll get to it.

I'm in the middle of converting 4wd 1800 GSR into authentic Evo 6 Tommi Makinen Edition...
complete with DIY stitch-welding, FoamSeal urethane, and DIY bodywork & paint job.
Also, upgrade Evo 6 RS2 with ProFlex suspension, wider wheels, EvoGreen turbo etc.
A lot to do meanwhile...

[cossie1]

Fairplay sounds like your busy

[Sanctifier]

^ ^ ^ Yup... just a little.

[bby_evo]

Hey Folks,

Well it seems that the solution for all EVO5/6 owners is to replace the ECU with one from a new model (7/8 etc).

So I was wondering, would this work for normal lancers as well?

I have a 1998 Lancer (a.k.a. Mirage in the US) with the re-flashing port that the Tactrix cable would hook up to. Would it be possible to replace the current ECU with one from a 2001-2003 lancer with the same engine (4g13)? Could I then reflash the new ECU using OpenECU?

This is exactly what I have been wondering. I have a usdm mirage, and I am looking to tune, but don't want to invest in the cable unless it will hook up with the ecu (connector is there). Has anyone tried a mirage/lancer/colt yet? If so, which motor? I have a 99 with the 4g15

[vercetti1765]

Here is my 3g eclipse 2000 rs rom for anyone who wants to look at it. Ecuflash read my h8 ecu just fine.