Page 1 of 2
'01 Eclipse GT m/t
Posted:
Mon Jul 25, 2011 9:50 am
by twistedturbo6692
Have the Openport 2.0, mitsu cable and Ecuflash downloaded. When I retrieve the factory files everything is good but I get a message basically saying it cannot be modified?! Any suggestions or am I dead in the water?
Ray
Re: '01 Eclipse GT m/t
Posted:
Mon Jul 25, 2011 1:14 pm
by todd-w
can you attach the rom here ??
Re: '01 Eclipse GT m/t
Posted:
Fri Jul 29, 2011 8:12 am
by twistedturbo6692
Re: '01 Eclipse GT m/t
Posted:
Tue Aug 02, 2011 4:32 am
by And
it might be the memory model or the flash method might not be correct for the ecu,
acording to the xml its a SH7052 and using the mitsukernel, could be worth looking in the ecu case to make sure its not a different processor
Andy
Re: '01 Eclipse GT m/t
Posted:
Mon Aug 08, 2011 6:44 am
by twistedturbo6692
Thanks Andy! I was wondering if pulling same year ECU off a different Eclipse/Stratus might work so long as its not coded to the other modules on the vehicle.
Ray
Re: '01 Eclipse GT m/t
Posted:
Wed Sep 28, 2011 3:22 am
by twistedturbo6692
Got everything going, the battery voltage was actually not where it should have been during the reading/write process. The only obstacle now is the immobilizer and how to delete it. Any clues, anyone?
Re: '01 Eclipse GT m/t
Posted:
Wed Sep 28, 2011 3:53 am
by And
you should see it in the periphery bits under FAA bit 3 i've attached the above rom with the immob disabled
Re: '01 Eclipse GT m/t
Posted:
Fri Sep 30, 2011 4:24 am
by twistedturbo6692
Thank you very very much Andy!
Ray
Re: '01 Eclipse GT m/t
Posted:
Sat Oct 01, 2011 12:35 pm
by twistedturbo6692
Hey Andy, I flashed that ROM to the vehicle and it still won't start. I used my scanner and I do get a P1610 immobilizer code, apparently it is still active any other ideas?
Ray
Re: '01 Eclipse GT m/t
Posted:
Sun Oct 02, 2011 12:27 am
by And
hi
i've tried editing the periphery bits again, if you want to try this
Re: '01 Eclipse GT m/t
Posted:
Sun Oct 02, 2011 3:13 pm
by twistedturbo6692
Hey Andy thanks for the file but no luck. I finally realized what you were talking about when you said periphery and bit 3. When I open up ECUflash none of my periphery tables are displayed even though I've copied and pasted the periphery stuff from an evo7base20081101.xml to my 96720008.xml. Obviously I am doing something wrong. Your help is greatly appreciated.
Ray
Re: '01 Eclipse GT m/t
Posted:
Sun Oct 02, 2011 10:55 pm
by And
here's my evo 7 base that contains the information
Re: '01 Eclipse GT m/t
Posted:
Mon Oct 03, 2011 3:50 am
by twistedturbo6692
Thanks Andy, I will try that and let you know how it goes.
Ray
Re: '01 Eclipse GT m/t
Posted:
Sat Oct 08, 2011 2:49 pm
by twistedturbo6692
Andy I got the periphery data pasted in my 96720008 xml and now its displayed in the hex file. Under periphery 0 (FAA) bit 3 I see the immobilizer enable/disable, I've flashed it just that way with no luck. The immobilizer is still appears to be intervening. I'm confused.
many thanks,
Ray
Re: '01 Eclipse GT m/t
Posted:
Wed Oct 12, 2011 4:48 am
by twistedturbo6692
Update, I got everything to work!!! I wiped everything out and re-installed ECUflash on the old laptop and made the necessary pasting. Thanks for all your help Andy.
Ray