openecu.org

Hi,

I am new to this. I had just received my cable a week ago. And i am try ing it onto my MY06 2.5 EURO STi and my friend MY05 2.0 EURO WRX. can anyone tell me what had been done wrong by me or the software.

The error for the MY05 is this vehicle interface does not support needed features. Unable to connect to vehicle interface.

And the MY06 is
-ssm2_init
- ecu id is 43 42 59 4006
- ssm2_cmd_0*81
- ssm2_cmd_0*83
- denso challenge-response
- challenge is 5E 18 1C 60
- response is 2F 77 ED 14



Cheers[/quote][/url]

My is a MY05 WRX 2.0 UK spec. Also hv problem to read the ECU. Can any 1 help..

00:14:39.905] Version 1.29.906
[00:14:39.915] 8 memory models read.
[00:14:42.739] 142 ROM metadata models read.
[00:14:42.739] checksum module "subarudbw" loaded.
[00:14:42.739] flashing tool "wrx02" loaded.
[00:14:42.749] flashing tool "wrx04" loaded.
[00:14:42.749] flashing tool "sti04" loaded.
[00:14:42.749] flashing tool "sti05" loaded.
[00:14:42.749] flashing tool "mitsukernel" loaded.
[00:14:42.749] flashing tool "mitsukernelocp" loaded.
[00:14:42.749] flashing tool "mitsubootloader" loaded.
[00:14:55.918] ssm2_init
[00:14:56.088] ECU ID is 3D 44 58 30 05
[00:14:56.088] ssm2_cmd_0x81

end.

Up date... Finally read my MY05 ECU rom.

Using ecuflash 1.3 to read it, then flash it w/ enginuity, for the time just some minor mod at the boost & AFR. Later decat then will go for the timing.

i have no problem with my MY02 edm wrx but i just can't seem to connect to a MY03 edm wrx.

The log is as follows

[01:42:16.671] Version 1.30.1095
[01:42:16.687] 8 memory models read.
[01:42:17.718] 145 ROM metadata models read.
[01:42:17.718] checksum module "subarudbw" loaded.
[01:42:17.718] flashing tool "wrx02" loaded.
[01:42:17.718] flashing tool "wrx04" loaded.
[01:42:17.718] flashing tool "sti04" loaded.
[01:42:17.718] flashing tool "sti05" loaded.
[01:42:17.718] flashing tool "mitsukernel" loaded.
[01:42:17.718] flashing tool "mitsukernelocp" loaded.
[01:42:17.718] flashing tool "mitsubootloader" loaded.
[01:42:36.468] SSM2 init
[01:42:36.640] [FF] A2 10 0F 2E 44 58 60 05 73 FA EB 80 2B C3 02 AA
00 10 00 60 CE 54 FC B0 60 00 00 E0 00 00 00 00
00 DC 00 00 55 1C 00 00 02 00 00 00 00 00 00 80
00 00 00 00 00 00 00 00
[01:42:36.640] SSM2 ECU ID is 2E 44 58 60 05
[01:42:36.640] SSM2 cmd_0x81
[01:43:30.609] 163840 byte image read.

I would really appreciate any help on this one.

try to use the 02-03 wrx to read, as my MY05 also use the 02-03 to read it, 04-05 cannot read the MY05 EDM.

i'm getting the same message for my 05 sti and i tried my sister 04 sti and does the same thing? i have the connector but do not know where to put them?

also tried to read the rom of a Impreza TS (1.6L) and i got this...

[14:50:48.859] Version 1.30.1095
[14:50:48.859] 8 memory models read.
[14:50:51.703] ROM metadata models A8DH200Y.xml is invalid.
[14:50:51.734] 146 ROM metadata models read.
[14:50:51.734] checksum module "subarudbw" loaded.
[14:50:51.734] flashing tool "wrx02" loaded.
[14:50:51.750] flashing tool "wrx04" loaded.
[14:50:51.750] flashing tool "sti04" loaded.
[14:50:51.750] flashing tool "sti05" loaded.
[14:50:51.750] flashing tool "mitsukernel" loaded.
[14:50:51.750] flashing tool "mitsukernelocp" loaded.
[14:50:51.750] flashing tool "mitsubootloader" loaded.
[14:51:00.703] SSM2 init
[14:51:00.875] [FF] A1 10 06 43 46 10 30 05 F3 EA AB 89 A2 0E 00 A8
00 00 00 60 CE 54 FC B8 01 00 00 E0 00 00 00 00
00 DC 00 00 71 1F 00 00 00 00 00 00 00 00 00 E0
00 00 00 00 00 00 00 00
[14:51:00.875] SSM2 ECU ID is 43 46 10 30 05
[14:51:00.875] SSM2 cmd_0x81
[14:51:17.578] denso02_bootloader_cmd_start
[14:51:18.968] denso02_bootloader_cmd_start
[14:51:20.359] denso02_bootloader_cmd_start
[14:51:21.750] denso02_bootloader_cmd_start
[14:51:23.140] denso02_bootloader_cmd_start
[14:51:23.750] kernel get version

What do I need to do to get it to work? Man, I am willing to pay to make it work with a TS.